• CT4, Tòa nhà Vimeco, Nguyễn Chánh, Cầu Giấy, Hà Nội
  • info@sbc-tt.com
    • HOTLINE TƯ VẤN
    • Tư vấn sơn: 0934518468 (Ms. Thoa)
    • Tư vấn sàn deck: 0941460336 (Mr.Ninh)
    • Tư vấn tôn: 0916688189 (Mr. Hiếu)
  • Việt Nam English

SP ® CLEAR – COLORLESS GLOSS COATING

MSP:

Mô tả Sản phẩm

SP®CLEAR is a solvent-free, colorless, glossy paint based on Epoxy resin 2 self-leveling components that create seamless surface finish. It is often used as a finishing coat for floor coatings, wall paintings, pseudo bulbs or overlaying paint surfaces that bring out gloss and aesthetics for light industrial floor and other floors that require long-term protection against chemicals, abrasives such as warehouses laboratories, factories, industrial plants, hospitals.
  • Colorless, super-gloss paint, waterproof effect.

It prevents the blistering, moss, mold, dust ..., due to the influence of weather.

  • Protect the surface from scratch thus enhance coating paint longevity.
  • Good impact, abrasion and chemical resistance.
  • Can be applied at thickness from 1-3 mm (depending on the method of construction).

Floor requirements: New concrete floors require a minimum of 28 days to fully cure before painting.

  • Minimum moisture content on the surface should not exceed 4%.
  • Ambient moisture content shall not exceed 85%.
  • Concrete marks must comply with concrete standards such as water / cement ratio, additives, minimum cement requirements as well as durability specifications.

Surface preparation: All types of concretes that are damaged with sticky chemicals and dirty impurities must be completely cleaned. The concrete surface should have a good roughness to ensure good adhesion.Concrete floors should be smooth and clean. Small defects and convex surface should be applied flat to avoid loss of paint.

  • If surface preparation is completed the previous day, it is necessary to vacuum the entire floor.
  • The best adhesion is obtained when the next coat is applied on the first coat without curing. If the subsequent coating time is exceeded, the surface should be sanded.

 

  • Stir part A and B separately to ensure that the paint does not settle in the bucket. Pour carefully, slowly from Part B to Part A, using a slow speed drill with a suitable stirrer, stirring for at least 2 minutes until uniformly.

Pour the mixture into the primed floor, using a scraper that can be adjusted to match the specified thickness of the film.

  • If the film is applied with a thickness of 1.5 mm or more, when the specified thickness has been reached, using rollers continuously roll on the surface of the film to remove all air in the paint film, roll until the film can reflect people’s shadow (the worker must wear stud shoes while walking on the wet paint).
  • The mixture should be used immediately. It shall not be left more than 30 minutes at 230C.
  • SPTHINNER - 305 can be used for thinning if needed, but not more than 2% by volume.
  • Cleaning tools and equipment after application with SPTHINNER 300 or SPTHINNER 305.
Màu sắc:

Colorless

Hàm lượng chẩt rắn:

Min 90%

Tỷ lệ:

0.5 – 1 m2/kg/ 1 mm or  13 - 15 m2/kg/layer (roll, spray)

Độ phủ lý thuyết:

1.05 ± 0.05 g/ml

Tỷ lệ trộn A/B:

1.7 / 1 (by volume)

Độ dày màng sơn:

Wet thickness: 1 - 3 mm

Dry thickness: 1 - 3 mm

TG khô(23°C):

Touchable dry 4 h

Hard dry 16 h

Thời gian phủ lớp kế (23°C):

Hard dry 16h

Chất pha loãng:

SPTHINNER 300

Sản phẩm liên quan

Liên hệ với chúng tôi

Sản phẩm mà bạn quan tâm

Tên sản phẩm:

Mã: